L-743 Press Alignment System

L-743 Press Alignment System Press Alignment Applications The L-743 Ultra-Precision Triple Scan® Laser is the ideal instrument to quickly and accurately calibrate the geometry of almost any kind of press. It is one of only 2 lasers in the world ( the other is the L-733) to offer 3 automatically rotating laser planes that are accurate enough for today' s ever-tightening tolerances. This creates a powerful tool that not only FINDS, but also FIXES geometry problems, all in a fraction of the time needed with conventional methods. The critical alignment of any press is the parallelism of the upper and lower rams to each other and squareness to the way ( gib) . The ways also need to be parallel. Poor alignment results in poorly formed parts that have to be scrapped and excess wear and tear on the press itself. > L-700 Spindle Laser Ideal for Punch Presses For punch presses, critical alignment is punch-to-die centering. Every time there is tool changeover, the die and punch need to be aligned for both center and angle. Since punches and dies are changed frequently, quick alignment becomes a necessity. The L-700 Spindle Alignment Laser is a great tool for this alignment. > Ram Parallelism Made Simple with Rotating Laser Planes Simple to use and easy to set up, the L-743 is the ideal instrument to measure upper-and-lower-ram parallelism. A simple setup procedure positions the laser plane parallel to the fixed ram. Targets are then repositioned to the movable ram and parallelism is easily measured. With Hamar Laser' s Plane 5 Software, setup and parallelism measurements are achieved even faster. And once the laser has been set up, if errors are found, they can be fixed immediately without having to change the setup. > Complete Way Squareness Measurements in Two Setups With the L-743' s built-in squareness ( each laser plane is square to each other with an accuracy of up to 1 arc second) , measuring the perpendicularity of the way ( gibs) to the rams is a simple task. In fact, with just two set-ups you can measure all four ways ( gibs) for squareness in two axes. And since the data is live, squareness errors can be fixed without changing the setup. Given that the laser has a range of 100 feet ( 30.5 meters) , the entire length of even the largest press can easily be measured for squareness. > Significantly Reduce Downtime when Changing Tools Changing punches and dies is time consuming and realignment is a necessity. If a ram is out of parallel to the dies, poor part quality and costly premature punch and die wear can occur. Inadequate alignment also results in excess wear on the press itself and can even lead to way ( gib) damage. With the high cost of machine overhauls, proper alignment becomes a big cost saver. The L-700 dramatically speeds the alignment process and provides a very accurate alignment. > Continuously Sweeping Lasers and Live Data Reduces Downtime Continuously sweeping lasers and live data output create a powerful combination to align presses up to 70% faster than traditional methods. Downed machines will be up and running, producing quality parts in record time. HLI' s continuously sweeping lasers are far superior to other point-and-shoot laser systems that require time-consuming manual laser rotation and target setup for each point measured. They also allow the use of multiple targets, which is especially helpful for large machine tools. By providing live alignment data, misalignment errors can be quickly and easily fixed without having to change the setup. This is a tremendous benefit, especially if you are used to using inside micrometers or tram bars, where the entire length of and axis must be measured before the straightness or flatness can be determined. > L-743 Significantly Reduces Stack Up Errors One of the biggest problems with aligning machine tools using conventional methods is that many different alignment tools must be used, requiring a lot of time and increasing stack-up errors. Another problem is that an alignment is only as good as the tools used to perform it. The machinist level is a good example: it has a resolution of .0005" per foot, not very accurate for today' s ever-tightening tolerances. The L-743' s laser planes, by contrast, have a flatness of 1/ 2 an arc second ( 0.00003" / ft or 0.0025mm/ M) in a 180º sweep and 1/ 4 arc second ( 0.000015" / ft or 0.001 mm/ M) in 90º sweep. The laser planes are square to each other to within 1 arc second ( 0.00006" / ft or 0.005 mm/ M) . They further have the advantage of creating a single reference from which to measure machine geometry, significantly reducing stack-up errors. > Squareness Built Into Laser Head One of the L-743' s greatest feature is its built-in squareness. You will be amazed at how quickly and easily the squareness of not just one axis, but multiple axes can be measured, usually with one setup! The L-743 takes just 10 minutes to setup and, unlike a cylindrical or knee square, the L-743 can check the entire length of a machine' s travel, up to 100 feet ( 30.5 meters) , not just 12" ( 305 mm) or 24" ( 610 mm) of it. Laser digital indicator, Digital Dial indicator, Alignment laser, shaft alignment system, spindle alignment system, bore alignment system, geometric alignment, kerataan sumbu saat instalasi mesin, kesejajaran, kerataan jasa alignment lubang, alignment shaft, Roll Aignment, Power Generation, Auto Industry, Fabrication, Machine Tools, Aerospace, Plastic Processing, Plastic Products, Geomatric Alignment. Distributor agent penjualan training service repair, upgrade dan perbaikan Jakarta - Indonesia TELP. 8611444 ( hunting) Call : 0815 614 1954, 0813 992 919 09, 0811 893 101