L-743 Injection Molding Machine Alignment System

L-743 Injection Molding Machine Alignment System INJECTION MOLDING MACHINE ALIGNMENT The L-743 Ultra-Precision Triple Scan® Laser is the ideal instrument to quickly and accurately calibrate the geometry of almost any kind of injection molding machine. It is one of only 2 lasers in the world ( the other is the L-733) to offer 3 automatically rotating laser planes that are accurate enough for today' s ever-tightening tolerances. This creates a powerful tool that not only FINDS, but also FIXES geometry problems, all in a fraction of the time needed with conventional methods. The critical alignments of any injection-molding machine are platen-to-platen parallelism and tie-bar squareness. Poor alignment results in premature wear on the mold, part flashing, and stress on, and potential breakage of, tie bars. > Platen-to-Platen Parallelism Made Simple with Rotating Laser Planes Simple to use and easy to set up, the L-743 is an ideal instrument to measure platen-to-platen parallelism. A simple setup procedure positions the laser plane parallel to the fixed platen. Targets are then repositioned to the movable platen and parallelism is easily measured. With Hamar Laser' s Plane 5 Software, setup and parallelism measurements are achieved even faster. And once the laser has been set up, if errors are found, they can be fixed immediately without having to change the setup. > Complete Tie-Bar Squareness Measurements in 2 Setups With the L-743' s built-in squareness ( each laser plane is square to each other) , measuring the perpendicularity of the tie bars to the platens is a simple task. In fact, with just two setups you can measure all four tie-bars for squareness in two axes. And since the data is live, squareness errors can be fixed without changing the setup. Given that the laser has a range of 100 feet ( 30.5 meters) in radius, even the entire length of the largest injection molding machines can easily be measured for squareness. > Significantly Reduce Downtime when Changing Molds Changing a mold is time consuming and realignment is a necessity. If a mold is slightly out of parallel to the platen, costly flashing and premature wear can occur. Inadequate alignment also results in excess wear on the injection-molding machine itself and can even lead to tie-bar breakage. With each tie bar costing at least $ 10, 000, proper alignment becomes a big cost saver. The L-743 not only speeds the alignment process significantly, but also reduces tooling and maintenance costs. > Continuously Sweeping Lasers and Live Data Reduces Downtime Continuously sweeping lasers and live data output create a powerful combination to align injection molding machines up to 70% faster than traditional methods. Downed machines will be up and running, producing quality parts in record time. HLI' s continuously sweeping lasers are far superior to other point-and-shoot laser systems that require time-consuming manual laser rotation and target setup for each point measured. They also allow the use of multiple targets, which is especially helpful for large machine tools. By providing live alignment data, misalignment errors can be quickly and easily fixed without having to change the setup. The targets come with 70-poind magnetic bases for maximum stability, so you can leave them on adjustment points ( even horizontally! ) when bringing the machine back into alignment. This is a tremendous benefit, especially if you use multiple targets, as you can literally watch the entire platen come back into alignment. > L-743 Significantly Reduces Stack Up Errors One of the biggest problems with aligning machine tools using conventional methods is that many different alignment tools must be used, requiring a lot of time and increasing stack-up errors. Another problem is that an alignment is only as good as the tools used to perform it. The machinist level is a good example: it has a resolution of .0005" per foot, not very accurate for today' s ever-tightening tolerances. The L-743' s laser planes, by contrast, are flat to 1/ 2 an arc second ( 0.00003" / ft or 0.0025mm/ M) in a 180° sweep and 1/ 4 arc second ( 0.000015" / ft or 0.001 mm/ M) in 90° sweep. The laser planes are square to each other with an accuracy of up to 1 arc second ( 0.00006" / ft or 0.005 mm/ M) . They further have the advantage of creating a single reference from which to measure machine geometry, significantly reducing stack-up errors. Laser digital indicator, Digital Dial indicator, Alignment laser, shaft alignment system, spindle alignment system, bore alignment system, geometric alignment, kerataan sumbu saat instalasi mesin, kesejajaran, kerataan jasa alignment lubang, alignment shaft, Roll Aignment, Power Generation, Auto Industry, Fabrication, Machine Tools, Aerospace, Plastic Processing, Plastic Products, Geomatric Alignment. Distributor agent penjualan training service repair, upgrade dan perbaikan Jakarta - Indonesia TELP. 8611444 ( hunting) Call : 0815 614 1954, 0813 992 919 09, 0811 893 101